Pit Boss Pro Series Igniter Not Working!

Ignition issues with the Pit Boss Pro Series can be a common concern. The problem often lies with the igniter not functioning as expected.

The Pit Boss Pro Series igniter not working could be due to a blown fuse. The igniter fuse is a critical component that protects the grill’s electrical system. If the fuse is blown, the igniter won’t work, and you’ll need to replace it.

The Pit Boss 1100 Pro Series igniter replacement is a straightforward process. You’ll need to first ensure the grill is turned off and cooled down. Then, locate the igniter, remove the faulty one, and install the new one. This should resolve the issue and get your grill back in working order.

The Pit Boss Pro Series 1600 igniter is another model that may experience similar issues. If your grill is not igniting, it could be due to a faulty igniter. Replacing the igniter in this model follows the same process as the 1100 series.

In general, if your Pit Boss problems or igniter is not working, it’s likely due to a faulty igniter or a blown fuse. Replacing these components should resolve the issue and allow you to get back to grilling.

causes of Pit Boss Pro series igniter not working and their fixes

Faulty Igniter

A common cause of the Pit Boss Pro Series igniter not working is a faulty igniter. This can occur due to wear and tear over time or due to manufacturing defects.

Fixing a Faulty Igniter

1. Identify the faulty igniter: The first step is to identify if the igniter is indeed faulty. This can be done by checking if the igniter glows red hot. If it doesn’t, it’s likely faulty.

2. Replace the igniter: If the igniter is faulty, it needs to be replaced. This involves purchasing a new igniter, turning off and cooling down the grill, removing the old igniter, and installing the new one.

Blown Fuse

The Pit Boss Pro Series igniter fuse is another common cause of ignition problems. The fuse can blow due to power surges or electrical faults, preventing the igniter from working.

Fixing a Blown Fuse

1. Identify the blown fuse: The first step is to identify if the fuse is blown. This can be done by checking the fuse for any visible signs of damage or using a multimeter to test it.

2. Replace the fuse: If the fuse is blown, it needs to be replaced. This involves purchasing a new fuse, turning off and cooling down the grill, removing the old fuse, and installing the new one.

Dirty Igniter

Dirt and grime can accumulate on the igniter over time, preventing it from working properly. This is a common issue, especially if the grill is not cleaned regularly.

Fixing a Dirty Igniter

1. Identify the dirty igniter: The first step is to identify if the igniter is dirty. This can be done by visually inspecting the igniter for any signs of dirt or grime.

2. Clean the igniter: If the igniter is dirty, it needs to be cleaned. This involves turning off and cooling down the grill, removing the igniter, cleaning it with a soft brush, and reinstalling it.

Learn More: Blue Smoke vs. White Smoke: A Battle of BBQ Techniques

Pit Boss Pro Series Igniter Test

Testing the igniter on your Pit Boss Pro Series grill is a crucial step in diagnosing ignition problems. The process is relatively straightforward and can be done with a few simple tools.

1. Start by ensuring that the grill is turned off and has had ample time to cool down. Safety should always be your top priority.

2. Next, locate the igniter. It’s typically found near the burner and is connected to a wire that leads back to the control panel.

3. Once you’ve located the igniter, observe it as you turn on the grill. A functioning igniter should glow red hot. If it doesn’t, it’s likely faulty.

4. For a more thorough test, you can use a multimeter. Disconnect the igniter from the wire and set your multimeter to test resistance.

A good igniter should show a resistance of around 40 to 90 ohms. If the resistance is significantly higher or lower, the igniter is likely faulty.

How to Replace Igniter on Pit Boss Pro Series?

Replacing the igniter on your Pit Boss Pro Series grill is a task that you can accomplish with a bit of time and the right tools. Here’s a step-by-step guide on how to do it.

1. First, ensure that the grill is turned off and has had enough time to cool down. This is crucial for your safety.

2. Next, locate the igniter. It’s usually near the burner and is connected to a wire that leads back to the control panel.

3. Once you’ve located the igniter, disconnect it from the wire. You may need to use a screwdriver or a similar tool to do this.

4. After disconnecting the old igniter, you can install the new one. Connect it to the wire and secure it in place. Make sure it’s installed correctly and securely.

5. After installing the new igniter, test it to ensure it’s working properly. Turn on the grill and observe the igniter. If it glows red hot, it’s working correctly. If not, double-check your installation.

Remember, if you’re not comfortable performing these tasks yourself, it’s always best to hire a professional or contact the manufacturer for assistance.

Learn More: Pit Boss Igniter Fuse Problems: Replace Now

FAQs

What Could Cause the Pit Boss Pro Series Igniter to Stop Working?

There are several reasons why the Pit Boss Pro Series igniter might stop working. These include a blown fuse, a faulty igniter, or a wiring issue. Regular maintenance and checks can help prevent these problems.

How Can I Test if the Pit Boss Pro Series Igniter is Working?

You can visually inspect the igniter while the grill is operating. A functioning igniter should glow red hot. For a more thorough test, use a multimeter to check the igniter’s resistance.

What Steps Should I Take to Replace the Igniter on a Pit Boss Pro Series?

Start by ensuring the grill is off and cooled down. Locate the igniter, disconnect it from the wire, and remove it. Install the new igniter, reconnect the wire, and test the grill to ensure it’s working properly.

How Can I Identify a Blown Fuse in the Pit Boss Pro Series?

You can identify a blown fuse by checking for visible signs of damage or using a multimeter to test it. If the fuse is blown, it will need to be replaced.

Is it possible for the Wiring to Cause the Pit Boss Pro Series Igniter to Not Work?

Yes, wiring issues can cause the igniter to stop working. If the wires are damaged or disconnected, the igniter won’t receive the electricity it needs to function.

How Often Should I Check the Pit Boss Pro Series Igniter for Issues?

Regular maintenance is key to ensuring your grill works properly. It’s a good idea to check the igniter and other components at the start of the grilling season and periodically throughout the year.

Learn More: 6 Common Green Mountain Grill Problems and Their Solutions